CESSNA / GENERAL AVIATION

Cessna 182

The Cessna 182 is a single-engine, high-wing, four-seat aircraft.

+ Compare aircraft

Choose the version you fly to narrow the edition-specific reading.

Occupants4
EngineLycoming IO-540-AB1A5, 230 hp
Propeller3-blade constant-speed McCauley
Maximum takeoff weight3,100 lb
Usable fuel87 US gal
Maximum cruise145 KTAS
Wingspan36 ft
Simulator ecosystemsMSFS
YOUR AIRCRAFT COMPANION

Start here

A few places to begin, from the aircraft’s story to the people who fly it.

THE AIRCRAFT

Meet Cessna 182

The Cessna 182 is a single-engine, high-wing, four-seat aircraft.

FAMILY, MODELS & VARIANTS

Cessna 182

Cessna → · Explore the family →

Aircraft type designators

No type designator selected for this reference.

HOW IT CAME TO BE

History & design

A family that began flying in 1955

Textron dates the Cessna 182’s first flight to September 1955. Over the following decades the Skylane appeared in several variants and in personal flying, training and cadet operations. Its long service history makes the model suffix and equipment list especially important when comparing simulator versions.

Textron Aviation · Seventy years of Cessna 182 flight ↗

Manufacturer anniversary history

The turbocharged branch

Textron introduced the T182T in 2001, paused its production in 2013 and announced its return in 2022. The returning model used a turbocharged TIO-540 installation, G1000 NXi avionics and an oxygen system. Those details belong to the Turbo Skylane, rather than every aircraft carrying the 182 name.

Textron Aviation · Return of the Turbo Skylane T182T ↗

Historical product announcement; equipment scoped to T182T

UNDER THE SKIN

Systems & details

Engine and propeller management are separate

The normally aspirated Skylane specification pairs a fuel-injected Lycoming with a constant-speed propeller. For the simulator pilot, RPM and engine loading therefore deserve separate attention. The aircraft’s power rating does not itself determine an appropriate joystick vibration gain.

Manufacturer powerplant table; force interpretation is editorial
Textron Aviation · Cessna Skylane specifications ↗

A familiar shape can contain a different panel

The current aircraft lists G1000 NXi avionics and a GFC 700 autopilot. Older and third-party simulator variants can represent different installations. A profile’s autopilot behaviour should follow the selected implementation, rather than the name on the fuselage alone.

Current manufacturer avionics; simulator distinction is editorial
Textron Aviation · Cessna Skylane specifications ↗
VIRTUAL VERSIONS

In your simulator

Systems, equipment and documentation for each developer’s aircraft.

Compare simulator versions →
MSFS 2020

C182 RG II

Carenado · Released

MSFS 2020Third-party add-on

Aircraft

Products and variants
ProductSimulatorProduct type
C182 RG II ↗ReleasedMSFS 2020 Aircraft
MSFS 2020

CT182T

Carenado · Released

MSFS 2020Third-party add-on

Aircraft

Products and variants
ProductSimulatorProduct type
CT182T ↗ReleasedMSFS 2020 Aircraft
GO TO THE SOURCE

Manuals & resources

Find your next read

Choose a topic for a short introduction and a link to the original source. Simulator references identify the developer and edition they cover.

Manufacturer, developer or authorized-product aircraft context

Cessna 182 — aircraft backgroundCessna 182

The Cessna 182 combines a high wing, four seats and one engine.

Aircraft-context passage, preserved text line 10; reviewed 2026-09-29

www.carenado.com · Read the source ↗

Developer documentation

C182 RG II — product listingC182 RG II · MSFS 2020

Individual product listing and edition passage reviewed 2026-09-29

www.carenado.com · Read the source ↗
CT182T — product listingCT182T · MSFS 2020

Individual product listing and edition passage reviewed 2026-09-29

www.carenado.com · Read the source ↗

Read the original documentation from the people who created it. Manuals open on their publisher’s website.

Manufacturer, developer or authorized-product aircraft context

↗Cessna 182 — aircraft backgroundwww.carenado.com · Aircraft-context passage, preserved text line 10; reviewed 2026-09-29

Product

↗C182 RG IIwww.carenado.com · Individual product listing and edition passage reviewed 2026-09-29

Aircraft reference

↗Cessna Skylane specificationsTextron Aviation · Current normally aspirated Skylane; checked 12 October 2026 ↗Seventy years of Cessna 182 flightTextron Aviation · Manufacturer anniversary account, 22 September 2025 ↗Return of the Turbo Skylane T182TTextron Aviation · Manufacturer announcement, 10 February 2022
AIRCRAFT AND FEEL

Built-in force-feedback profiles

Read the documentary basis, editable starting settings and remaining questions for the aircraft you fly. Each explanation refers to the exact profile revision shown.

Catalogue programme-20261022-v1 · 7 profile choices

FFB-BRIDGE BUILT-IN PROFILE

Carenado C182Q Skylane

Free and ProRevision 3Inherited starting point

The Cessna 182 is a single-engine, high-wing, four-seat aircraft.

Aircraft and simulator scope

  • Carenado C182Q Skylane · Carenado · MSFS 2020 · Add-on starting point
  • Carenado C182Q Skylane · Carenado · MSFS 2024 · Add-on starting point

The simulator model and controls

Carenado C182Q Skylane is the selected Carenado configuration.

How this profile feels

Spring resistance builds with the selected airspeed response. A separate aerodynamic term adds speed-dependent control load.

Pitch-trim relief is off. Autopilot following is off.

Aircraft and configuration

The Cessna 182 is a single-engine, high-wing, four-seat aircraft.

About the values

Strengths are normalized hardware-feel settings. They set the effect balance; hand force depends on the device and its limits. The IAS reference is a tuning value.

Documentary review and sources

These decisions describe the documentary basis and remaining gaps for this revision. Aircraft documentation and a starting setting describe different kinds of evidence.

Aircraft and variant
Inherited

Carenado C182Q Skylane is the selected Carenado configuration.

Flight controls
Inherited

The Cessna 182 is a single-engine, high-wing, four-seat aircraft.

Trim
Inherited

The profile uses the trim behaviour configured below. Pitch relief is off, with stored authority 0; roll authority is 0.

Autopilot and stability
Inherited

Autopilot following is off; the configured spring and load retain the hardware feel.

Equipment
Inherited

The Cessna 182 is a single-engine, high-wing, four-seat aircraft.

Speeds and limits
Inherited

The indicated-speed references set the profile response scale; they are separate from aircraft operating limits.

Simulator integration
Inherited

The profile targets msfs2020, msfs2024. Add-on-specific controls use only the supported references configured by this profile.

Force-feedback settings
Inherited

The settings define the profile’s effect balance. Device output limits affect physical hand force.

Starting settings and their rationale

These configured values are starting estimates. The explanations describe what each setting controls; physical validation appears separately below.

Estimated starting settings · revision 3
SettingStarting valueWhat it controls and why
Spring strengthStarting value0.74 What it controls and whyThis profile uses reversible-control loading for Cessna 182. The baseline spring is 0.74. Its low-speed blend reaches baseline strength at 62.5 KIAS.
Master force gainStarting value0.85 What it controls and whyScales overall profile strength while preserving effect balance, subject to device and output limits.
Profile force gainStarting value0.8 What it controls and whyThe aerodynamic-load gain is 0.8 with an indicated-speed reference of 125 KIAS. This supplies speed-dependent loading alongside the spring.
Force tuning speed/referenceStarting value125.0 ktWhat it controls and whySets the IAS reference for aerodynamic loading. It is an estimate, not published cruise TAS or a flight limit.
Spring response reference speedStarting value62.5 ktWhat it controls and whySets the IAS where the low-speed blend reaches baseline strength; high-speed stiffening also uses it.
Aileron force scaleStarting value0.72 What it controls and whyRoll and pitch aerodynamic scales are 0.72 and 1, respectively. They set the aerodynamic axis balance. No custom spring-travel curve is enabled.
Elevator force scaleStarting value1 What it controls and whyScales pitch aerodynamic loading; pitch spring travel and trim responses are separate settings.
Trim feelStarting valueDisabled What it controls and whyRetained for compatibility and group membership. Trim relief, rather than this flag, controls centre movement.
Trim reliefStarting valueDisabled What it controls and whyAllows trim relief with supported control law and valid telemetry. Axis authorities set its amount.
Autopilot followStarting valueDisabled What it controls and whyAutopilot following is off; the configured spring and load retain the hardware feel.
Autopilot neutral holdStarting valueDisabled What it controls and whyPermits centering hold during a supported AP state, separate from following a moving target.
Output force limitStarting value0.55 What it controls and whyCaps directed-force output. Native spring effects and device limits remain separate.
All 44 starting settings and their rationale

The settings define the profile’s effect balance. Device output limits affect physical hand force.

Estimated starting settings · revision 3
SettingStarting valueWhat it controls and why
Spring strengthStarting value0.74 What it controls and whyThis profile uses reversible-control loading for Cessna 182. The baseline spring is 0.74. Its low-speed blend reaches baseline strength at 62.5 KIAS.
Spring deadbandStarting value0.04 What it controls and whySets travel around the centre before the baseline spring resists. Smaller values engage it sooner.
Profile force gainStarting value0.8 What it controls and whyThe aerodynamic-load gain is 0.8 with an indicated-speed reference of 125 KIAS. This supplies speed-dependent loading alongside the spring.
Master force gainStarting value0.85 What it controls and whyScales overall profile strength while preserving effect balance, subject to device and output limits.
QBlend EnabledStarting valueEnabled What it controls and whyAllows baseline spring strength to rise with indicated airspeed where the control law permits it.
QSpring Minimum FactorStarting value0.55 What it controls and whySets low-speed spring strength as a fraction of baseline when blending is enabled. One keeps full strength.
QSpring Start KnotsStarting value8 ktWhat it controls and whySets the IAS where the low-speed spring blend starts rising. This is a feel threshold, not a flight limit.
Spring response reference speedStarting value62.5 ktWhat it controls and whySets the IAS where the low-speed blend reaches baseline strength; high-speed stiffening also uses it.
Force tuning speed/referenceStarting value125.0 ktWhat it controls and whySets the IAS reference for aerodynamic loading. It is an estimate, not published cruise TAS or a flight limit.
Airspeed spring stiffening gainStarting value0.15 What it controls and whyThe high-speed spring-stiffening gain is 0.15. It strengthens the permitted spring response above 62.5 KIAS, with the squared-speed ratio capped at 5.
Airspeed spring stiffening limitStarting value5 What it controls and whyLimits the squared airspeed ratio used for high-speed spring stiffening; it is not a device-force cap.
Aileron force scaleStarting value0.72 What it controls and whyRoll and pitch aerodynamic scales are 0.72 and 1, respectively. They set the aerodynamic axis balance. No custom spring-travel curve is enabled.
Elevator force scaleStarting value1 What it controls and whyScales pitch aerodynamic loading; pitch spring travel and trim responses are separate settings.
Output force limitStarting value0.55 What it controls and whyCaps directed-force output. Native spring effects and device limits remain separate.
Trim feelStarting valueDisabled What it controls and whyRetained for compatibility and group membership. Trim relief, rather than this flag, controls centre movement.
Trim reliefStarting valueDisabled What it controls and whyAllows trim relief with supported control law and valid telemetry. Axis authorities set its amount.
Elevator AuthorityStarting value0 What it controls and whyThe profile uses the trim behaviour configured below. Pitch relief is off, with stored authority 0; roll authority is 0.
Aileron AuthorityStarting value0 What it controls and whyScales supported roll-trim relief and permitted centre movement. Zero removes roll response.
Force Trim EnabledStarting valueDisabled What it controls and whyEnables local force trim, separate from aircraft-owned trim and add-on integration qualification.
GLoad EnabledStarting valueEnabled What it controls and whyAllows load-factor changes to modify permitted spring laws. Passive fly-by-wire feel can suppress it.
Rate Damping EnabledStarting valueEnabled What it controls and whyEnables rate damping with the configured coefficients and control law.
Autopilot followStarting valueDisabled What it controls and whyAutopilot following is off; the configured spring and load retain the hardware feel.
Autopilot follow authorityStarting value0.1 What it controls and whySets admitted AP-follow gain, not a percentage of travel. Runtime ownership and input limits still apply.
Autopilot neutral holdStarting valueDisabled What it controls and whyPermits centering hold during a supported AP state, separate from following a moving target.
Autopilot neutral hold strengthStarting value0.6 What it controls and whySets admitted AP neutral-hold strength; inactive while neutral hold is disabled.
EnabledStarting valueEnabled What it controls and whyEnables aerodynamic cues; each still needs nonzero strength and its simulator conditions.
GainStarting value0.35 What it controls and whySets stall-buffet strength. Zero removes the cue without changing simulator stalls or warnings.
GainStarting value0 What it controls and whySets high-Mach buffet strength; onset and full-strength thresholds are separate.
GainStarting value0 What it controls and whySets flap buffet at the configured position and speed gates. Flap movement texture is separate.
Maximum flap indexStarting value4 What it controls and whySets the final flap index for detent normalization. UP plus three detents uses maximum index3.
Minimum flap indexStarting value2 What it controls and whySets the first flap detent that admits buffet; this is a handle index, not degrees.
GainStarting value0 What it controls and whySets gear aerodynamic buffet; movement and ground-contact cues are separate.
Shaker EnabledStarting valueDisabled What it controls and whyPermits shaker at supported warning conditions; the switch does not establish aircraft equipment.
Stick shaker amplitudeStarting value0.5 What it controls and whySets triggered shaker strength; inactive while the shaker feature is disabled.
EnabledStarting valueEnabled What it controls and whyEnables ground effects; each still needs its own strength and contact or motion telemetry.
GainStarting value0.4 What it controls and whySets rolling texture strength, modified by speed, surface and undercarriage configuration.
GainStarting value0.25 What it controls and whySets gear-bump texture during ground motion, separate from touchdown impact.
GainStarting value0.65 What it controls and whySets landing-impact strength; landing telemetry and response shape determine the pulse.
GainStarting value0 What it controls and whySets reverse-thrust vibration with valid reverser and engine conditions. Zero removes the cue.
EnabledStarting valueEnabled What it controls and whyEnables engine cues with nonzero settings and valid running-engine telemetry.
GainStarting value0.12 What it controls and whySets estimated engine vibration using configured telemetry and response, not measured cockpit vibration.
EnabledStarting valueEnabled What it controls and whyEnables accessory cues with configured strengths and observed accessory movement.
GainStarting value0.12 What it controls and whySets texture from observed flap movement; a command without movement does not establish the cue.
GainStarting value0 What it controls and whySets texture from observed gear movement, separate from aerodynamic and touchdown effects.
Limits and open questions
  • Conventional manual control approximation for this aircraft, with modest aerodynamic loading. Accessory hydraulics and avionics do not establish powered primary controls.
  • Exact trim-to-inceptor relationship is not established by the available product source; automatic neutral shift remains disabled, with no inherited trim coefficient.
  • Published AP equipment does not supply a calibrated servo or inceptor target. Follow and neutral hold remain disabled; no interface copied from another developer.
  • Read-only native simulator channels; position input preserved. Actual accessory motion only. Custom systems, engine failures and historical operating procedures do not create unqualified force commands. Installed title/version and hardware travel remain acceptance limits.
  • 125.0 KIAS is an estimated control-feel reference, not cruise TAS, V-speeds or an operating limit.
  • Spring 0.74, lateral scale 0.72, trim relief 0/0; editable estimates, not measured hand forces.
  • Physical and installed-aircraft checks are deferred. Save this profile as the aircraft default if telemetry omits its developer or configuration.
  • Only actual accessory-position changes drive movement textures. No pressure-dependent failures, guessed servo outputs or input compensation.
  • Earlier family-derived force values are superseded by this explicit review. Source limitations are not installed qualification.

Physical validation

No physical force validation is recorded in this public catalogue for this revision. Documentary review and software checks do not establish how a particular device feels.

FFB-Bridge maintains this profile’s revisions and tuning discussion.

Revision 3 and download availability in FFB-Bridge ↗
Exact profile identity
Profile
addon-carenado-c182q-skylane
Artifact SHA-256
80fe5539ac95f15e87fef60e1e083db536e62bd675d7c01139b512cdbfbf1db3
Bytes
13788
Spring strength
Forces.SpringStrength
Spring deadband
Forces.SpringDeadband
Profile force gain
Forces.ForceGain
Master force gain
Forces.MasterGain
QBlend Enabled
Forces.QBlendEnabled
QSpring Minimum Factor
Forces.QSpringMinimumFactor
QSpring Start Knots
Forces.QSpringStartKnots
Spring response reference speed
Forces.QSpringFullKnots
Force tuning speed/reference
Forces.CruiseSpeedRefKnots
Airspeed spring stiffening gain
Forces.SpringAirspeedStiffenGain
Airspeed spring stiffening limit
Forces.SpringAirspeedStiffenCap
Aileron force scale
Forces.AileronForceScale
Elevator force scale
Forces.ElevatorForceScale
Output force limit
Forces.MaxOutputForce
Trim feel
StickFeel.TrimFeelEnabled
Trim relief
StickFeel.TrimReliefEnabled
Elevator Authority
StickFeel.TrimRelief.ElevatorAuthority
Aileron Authority
StickFeel.TrimRelief.AileronAuthority
Force Trim Enabled
StickFeel.ForceTrimEnabled
GLoad Enabled
StickFeel.GLoadEnabled
Rate Damping Enabled
StickFeel.RateDampingEnabled
Autopilot follow
Autopilot.FollowEnabled
Autopilot follow authority
Autopilot.FollowAuthority
Autopilot neutral hold
Autopilot.NeutralHoldEnabled
Autopilot neutral hold strength
Autopilot.NeutralHoldStrength
Enabled
Aero.Enabled
Gain
Aero.Stall.Gain
Gain
Aero.Mach.Gain
Gain
Aero.Flap.Gain
Maximum flap index
Aero.Flap.MaxFlapIndex
Minimum flap index
Aero.Flap.MinFlapIndex
Gain
Aero.Gear.Gain
Shaker Enabled
Aero.ShakerEnabled
Stick shaker amplitude
Aero.Shaker.Amplitude
Enabled
Ground.Enabled
Gain
Ground.Rumble.Gain
Gain
Ground.Bumps.Gain
Gain
Ground.Thump.Gain
Gain
Ground.Reverse.Gain
Enabled
Engine.Enabled
Gain
Engine.Rumble.Gain
Enabled
Mechanical.Enabled
Gain
Mechanical.FlapMotion.Gain
Gain
Mechanical.GearMotion.Gain
Explore all built-in profile references →

Content expanded · What’s new

Something missing or a source that needs attention?

Suggest a correction ↗