PIPER / TURBOPROP

Piper M500

The Piper M500 is a single-engine, cabin-class turboprop used for personal and corporate transport.

+ Compare aircraft

Choose the version you fly to narrow the edition-specific reading.

EnginePratt & Whitney PT6A-42A, flat-rated to 500 shp
PropellerHartzell four-blade; constant-speed, feathering and reversible
Usable fuel170 US gal
Wingspan43 ft
Length29.6 ft
Height11.3 ft
Simulator ecosystemsX-Plane
YOUR AIRCRAFT COMPANION

Start here

A few places to begin, from the aircraft’s story to the people who fly it.

Aircraft history

Meet the aircraft

The Piper M500 is a single-engine, cabin-class turboprop used for personal and corporate transport.

Piper M500

store.x-plane.org · Read more ↗
THE AIRCRAFT

Meet Piper M500

The Piper M500 is a single-engine, cabin-class turboprop used for personal and corporate transport.

FAMILY, MODELS & VARIANTS

Piper M500

Piper → · Explore the family →

Aircraft type designators

No type designator selected for this reference.

HOW IT CAME TO BE

History & design

The Meridian becomes the M500

Piper introduced the Meridian M500 in April 2015. It retained the 500 shp PT6A-42A while updating avionics, cockpit protections and the cabin offering. The launch connected the established Meridian airframe with the M-series product identity.

Piper Aircraft · Piper debuts M500, April 2015 ↗

2015 launch

The cockpit becomes part of the development story

The 2015 announcement highlighted electronic stability and underspeed protection, coupled go-around, level mode and integrated digital pressurisation. These features identify the launch-era avionics configuration; current production lists G1000 NXi equipment.

Piper Aircraft · Piper debuts M500, April 2015 ↗

2015 launch; equipment varies by production standard

UNDER THE SKIN

Systems & details

Propeller and turbine behaviour belong together

The manufacturer specifies a constant-speed, full-feathering and reversible propeller. That makes propeller mode and power management part of the M500’s identity, alongside the turbine engine; simulator support depends on the selected implementation.

M500: current manufacturer specification; October 2026
Piper Aircraft · M500 specifications ↗

A six-place cabin and updated cockpit

Piper’s 2015 launch announcement paired the M500’s updated avionics with a six-place cabin, club seating and revised passenger fittings. The pressurised turboprop retained the 500-shaft-horsepower PT6A-42A engine. Piper quoted a 260-knot maximum cruise and 1,000-nautical-mile range for the launch aircraft. Those published performance figures and the original G1000 equipment describe that offering; later avionics updates and particular simulator packages need their own configuration labels.

Piper M500 2015 launch configuration
Piper Aircraft · Piper debuts M500, April 2015 ↗
VIRTUAL VERSIONS

In your simulator

Systems, equipment and documentation for each developer’s aircraft.

X-Plane 12

PA-46 M500

X-Aerodynamics · Released

X-Plane 12Third-party add-on

Aircraft

Products and variants
ProductSimulatorProduct type
PA-46 M500 ↗ReleasedX-Plane 12 Aircraft
GO TO THE SOURCE

Manuals & resources

Find your next read

Choose a topic for a short introduction and a link to the original source. Simulator references identify the developer and edition they cover.

Manufacturer, developer or authorized-product aircraft context

Piper M500 — aircraft backgroundPiper M500

Background on the cabin-class, single-engine Piper M500 turboprop.

Aircraft-context passage, preserved text line 51; reviewed 2026-09-29

store.x-plane.org · Read the source ↗

Developer documentation

PA-46 M500 — product listingPA-46 M500 · X-Plane 12

Individual product listing and edition passage reviewed 2026-09-29

store.x-plane.org · Read the source ↗

Read the original documentation from the people who created it. Manuals open on their publisher’s website.

Manufacturer, developer or authorized-product aircraft context

↗Piper M500 — aircraft backgroundstore.x-plane.org · Aircraft-context passage, preserved text line 51; reviewed 2026-09-29

Manufacturer aircraft information

↗M500 specificationsPiper Aircraft · M500: current manufacturer specification; October 2026 ↗Piper debuts M500, April 2015Piper Aircraft · Launch announcement, 14 April 2015
AIRCRAFT AND FEEL

Built-in force-feedback profiles

Read the documentary basis, editable starting settings and remaining questions for the aircraft you fly. Each explanation refers to the exact profile revision shown.

Catalogue programme-20261022-v1 · 4 profile choices

FFB-BRIDGE BUILT-IN PROFILE

Carenado PA46-500TP Meridian

Free and ProRevision 1Partial review

The Piper M500 is a single-engine, cabin-class turboprop used for personal and corporate transport.

Aircraft and simulator scope

  • Carenado PA46-500TP Meridian · Carenado · X-Plane 11 · Add-on starting point

Carenado PA46-500TP Meridian · Historical XP11 catalogue scope; compatibility is not transferred to XP12.

The simulator model and controls

Carenado PA46-500TP Meridian is the selected Carenado configuration.

How this profile feels

Spring resistance builds with the selected airspeed response. A separate aerodynamic term adds speed-dependent control load.

Valid trim provides the configured pressure relief. Autopilot following is off.

Aircraft and configuration

Carenado identifies PA46-500TP Malibu Meridian G1000 for XP11.

About the values

Strengths are normalized hardware-feel settings. They set the effect balance; hand force depends on the device and its limits. The IAS reference is a tuning value.

What the documentation establishes

Carenado identifies PA46-500TP Malibu Meridian G1000 for XP11.

Documentary review and sources

These decisions describe the documentary basis and remaining gaps for this revision. Aircraft documentation and a starting setting describe different kinds of evidence.

Aircraft and variant
Reviewed

Carenado PA46-500TP Meridian is the selected Carenado configuration.

Flight controls
Not yet reviewed

The Piper M500 is a single-engine, cabin-class turboprop used for personal and corporate transport.

Trim
Not yet reviewed

The profile uses the trim behaviour configured below. Pitch authority 0.3 provides load relief and permitted centre movement; roll authority is 0.

Autopilot and stability
Not yet reviewed

Autopilot following is off; the configured spring and load retain the hardware feel.

Equipment
Not yet reviewed

Carenado identifies PA46-500TP Malibu Meridian G1000 for XP11.

Speeds and limits
Not yet reviewed

The indicated-speed references set the profile response scale; they are separate from aircraft operating limits.

Simulator integration
Not yet reviewed

The profile targets xplane11. Add-on-specific controls use only the supported references configured by this profile.

Force-feedback settings
Not yet reviewed

The settings define the profile’s effect balance. Device output limits affect physical hand force.

Starting settings and their rationale

These configured values are starting estimates. The explanations describe what each setting controls; physical validation appears separately below.

Estimated starting settings · revision 1
SettingStarting valueWhat it controls and why
Spring strengthStarting value0.74 What it controls and whyThis profile uses reversible-control loading for Piper M500. The baseline spring is 0.74. Its low-speed blend reaches baseline strength at 95 KIAS.
Master force gainStarting value0.85 What it controls and whyScales overall profile strength while preserving effect balance, subject to device and output limits.
Profile force gainStarting value0.68 What it controls and whyThe aerodynamic-load gain is 0.68 with an indicated-speed reference of 220 KIAS. This supplies speed-dependent loading alongside the spring.
Force tuning speed/referenceStarting value220.0 ktWhat it controls and whySets the IAS reference for aerodynamic loading. It is an estimate, not published cruise TAS or a flight limit.
Spring response reference speedStarting value95 ktWhat it controls and whySets the IAS where the low-speed blend reaches baseline strength; high-speed stiffening also uses it.
Aileron force scaleStarting value0.72 What it controls and whyRoll and pitch aerodynamic scales are 0.72 and 1, respectively. They set the aerodynamic axis balance. No custom spring-travel curve is enabled.
Elevator force scaleStarting value1.0 What it controls and whyScales pitch aerodynamic loading; pitch spring travel and trim responses are separate settings.
Trim feelStarting valueEnabled What it controls and whyRetained for compatibility and group membership. Trim relief, rather than this flag, controls centre movement.
Trim reliefStarting valueEnabled What it controls and whyAllows trim relief with supported control law and valid telemetry. Axis authorities set its amount.
Autopilot followStarting valueDisabled What it controls and whyAutopilot following is off; the configured spring and load retain the hardware feel.
Autopilot neutral holdStarting valueDisabled What it controls and whyPermits centering hold during a supported AP state, separate from following a moving target.
Output force limitStarting value0.55 What it controls and whyCaps directed-force output. Native spring effects and device limits remain separate.
All 44 starting settings and their rationale

The settings define the profile’s effect balance. Device output limits affect physical hand force.

Estimated starting settings · revision 1
SettingStarting valueWhat it controls and why
Spring strengthStarting value0.74 What it controls and whyThis profile uses reversible-control loading for Piper M500. The baseline spring is 0.74. Its low-speed blend reaches baseline strength at 95 KIAS.
Spring deadbandStarting value0.05 What it controls and whySets travel around the centre before the baseline spring resists. Smaller values engage it sooner.
Profile force gainStarting value0.68 What it controls and whyThe aerodynamic-load gain is 0.68 with an indicated-speed reference of 220 KIAS. This supplies speed-dependent loading alongside the spring.
Master force gainStarting value0.85 What it controls and whyScales overall profile strength while preserving effect balance, subject to device and output limits.
QBlend EnabledStarting valueEnabled What it controls and whyAllows baseline spring strength to rise with indicated airspeed where the control law permits it.
QSpring Minimum FactorStarting value0.55 What it controls and whySets low-speed spring strength as a fraction of baseline when blending is enabled. One keeps full strength.
QSpring Start KnotsStarting value30.8 ktWhat it controls and whySets the IAS where the low-speed spring blend starts rising. This is a feel threshold, not a flight limit.
Spring response reference speedStarting value95 ktWhat it controls and whySets the IAS where the low-speed blend reaches baseline strength; high-speed stiffening also uses it.
Force tuning speed/referenceStarting value220.0 ktWhat it controls and whySets the IAS reference for aerodynamic loading. It is an estimate, not published cruise TAS or a flight limit.
Airspeed spring stiffening gainStarting value0.1 What it controls and whyThe high-speed spring-stiffening gain is 0.1. It strengthens the permitted spring response above 95 KIAS, with the squared-speed ratio capped at 5.
Airspeed spring stiffening limitStarting value5 What it controls and whyLimits the squared airspeed ratio used for high-speed spring stiffening; it is not a device-force cap.
Aileron force scaleStarting value0.72 What it controls and whyRoll and pitch aerodynamic scales are 0.72 and 1, respectively. They set the aerodynamic axis balance. No custom spring-travel curve is enabled.
Elevator force scaleStarting value1.0 What it controls and whyScales pitch aerodynamic loading; pitch spring travel and trim responses are separate settings.
Output force limitStarting value0.55 What it controls and whyCaps directed-force output. Native spring effects and device limits remain separate.
Trim feelStarting valueEnabled What it controls and whyRetained for compatibility and group membership. Trim relief, rather than this flag, controls centre movement.
Trim reliefStarting valueEnabled What it controls and whyAllows trim relief with supported control law and valid telemetry. Axis authorities set its amount.
Elevator AuthorityStarting value0.3 What it controls and whyThe profile uses the trim behaviour configured below. Pitch authority 0.3 provides load relief and permitted centre movement; roll authority is 0.
Aileron AuthorityStarting value0 What it controls and whyScales supported roll-trim relief and permitted centre movement. Zero removes roll response.
Force Trim EnabledStarting valueDisabled What it controls and whyEnables local force trim, separate from aircraft-owned trim and add-on integration qualification.
GLoad EnabledStarting valueEnabled What it controls and whyAllows load-factor changes to modify permitted spring laws. Passive fly-by-wire feel can suppress it.
Rate Damping EnabledStarting valueEnabled What it controls and whyEnables rate damping with the configured coefficients and control law.
Autopilot followStarting valueDisabled What it controls and whyAutopilot following is off; the configured spring and load retain the hardware feel.
Autopilot follow authorityStarting value0.1 What it controls and whySets admitted AP-follow gain, not a percentage of travel. Runtime ownership and input limits still apply.
Autopilot neutral holdStarting valueDisabled What it controls and whyPermits centering hold during a supported AP state, separate from following a moving target.
Autopilot neutral hold strengthStarting value0.6 What it controls and whySets admitted AP neutral-hold strength; inactive while neutral hold is disabled.
EnabledStarting valueEnabled What it controls and whyEnables aerodynamic cues; each still needs nonzero strength and its simulator conditions.
GainStarting value0.28 What it controls and whySets stall-buffet strength. Zero removes the cue without changing simulator stalls or warnings.
GainStarting value0 What it controls and whySets high-Mach buffet strength; onset and full-strength thresholds are separate.
GainStarting value0.14 What it controls and whySets flap buffet at the configured position and speed gates. Flap movement texture is separate.
Maximum flap indexStarting value2 What it controls and whySets the final flap index for detent normalization. UP plus three detents uses maximum index3.
Minimum flap indexStarting value2 What it controls and whySets the first flap detent that admits buffet; this is a handle index, not degrees.
GainStarting value0.12 What it controls and whySets gear aerodynamic buffet; movement and ground-contact cues are separate.
Shaker EnabledStarting valueDisabled What it controls and whyPermits shaker at supported warning conditions; the switch does not establish aircraft equipment.
Stick shaker amplitudeStarting value0.5 What it controls and whySets triggered shaker strength; inactive while the shaker feature is disabled.
EnabledStarting valueEnabled What it controls and whyEnables ground effects; each still needs its own strength and contact or motion telemetry.
GainStarting value0.42 What it controls and whySets rolling texture strength, modified by speed, surface and undercarriage configuration.
GainStarting value0.32 What it controls and whySets gear-bump texture during ground motion, separate from touchdown impact.
GainStarting value0.82 What it controls and whySets landing-impact strength; landing telemetry and response shape determine the pulse.
GainStarting value0.48 What it controls and whySets reverse-thrust vibration with valid reverser and engine conditions. Zero removes the cue.
EnabledStarting valueEnabled What it controls and whyEnables engine cues with nonzero settings and valid running-engine telemetry.
GainStarting value0.06 What it controls and whySets estimated engine vibration using configured telemetry and response, not measured cockpit vibration.
EnabledStarting valueEnabled What it controls and whyEnables accessory cues with configured strengths and observed accessory movement.
GainStarting value0.12 What it controls and whySets texture from observed flap movement; a command without movement does not establish the cue.
GainStarting value0.12 What it controls and whySets texture from observed gear movement, separate from aerodynamic and touchdown effects.
Limits and open questions
  • Its G1000 is based on Laminar's default unit. PA46 piston Malibu and turbine Meridian equipment are distinct; a family label does not qualify force follow.
  • No simulator launch or physical force validation.

Physical validation

No physical force validation is recorded in this public catalogue for this revision. Documentary review and software checks do not establish how a particular device feels.

FFB-Bridge maintains this profile’s revisions and tuning discussion.

Revision 1 and download availability in FFB-Bridge ↗
Exact profile identity
Profile
addon-carenado-pa46-500tp-meridian
Artifact SHA-256
c08a4883b4df53b473489a7ee1ec3f4055f49abf0883782ccc629f9750b30202
Bytes
12385
Spring strength
Forces.SpringStrength
Spring deadband
Forces.SpringDeadband
Profile force gain
Forces.ForceGain
Master force gain
Forces.MasterGain
QBlend Enabled
Forces.QBlendEnabled
QSpring Minimum Factor
Forces.QSpringMinimumFactor
QSpring Start Knots
Forces.QSpringStartKnots
Spring response reference speed
Forces.QSpringFullKnots
Force tuning speed/reference
Forces.CruiseSpeedRefKnots
Airspeed spring stiffening gain
Forces.SpringAirspeedStiffenGain
Airspeed spring stiffening limit
Forces.SpringAirspeedStiffenCap
Aileron force scale
Forces.AileronForceScale
Elevator force scale
Forces.ElevatorForceScale
Output force limit
Forces.MaxOutputForce
Trim feel
StickFeel.TrimFeelEnabled
Trim relief
StickFeel.TrimReliefEnabled
Elevator Authority
StickFeel.TrimRelief.ElevatorAuthority
Aileron Authority
StickFeel.TrimRelief.AileronAuthority
Force Trim Enabled
StickFeel.ForceTrimEnabled
GLoad Enabled
StickFeel.GLoadEnabled
Rate Damping Enabled
StickFeel.RateDampingEnabled
Autopilot follow
Autopilot.FollowEnabled
Autopilot follow authority
Autopilot.FollowAuthority
Autopilot neutral hold
Autopilot.NeutralHoldEnabled
Autopilot neutral hold strength
Autopilot.NeutralHoldStrength
Enabled
Aero.Enabled
Gain
Aero.Stall.Gain
Gain
Aero.Mach.Gain
Gain
Aero.Flap.Gain
Maximum flap index
Aero.Flap.MaxFlapIndex
Minimum flap index
Aero.Flap.MinFlapIndex
Gain
Aero.Gear.Gain
Shaker Enabled
Aero.ShakerEnabled
Stick shaker amplitude
Aero.Shaker.Amplitude
Enabled
Ground.Enabled
Gain
Ground.Rumble.Gain
Gain
Ground.Bumps.Gain
Gain
Ground.Thump.Gain
Gain
Ground.Reverse.Gain
Enabled
Engine.Enabled
Gain
Engine.Rumble.Gain
Enabled
Mechanical.Enabled
Gain
Mechanical.FlapMotion.Gain
Gain
Mechanical.GearMotion.Gain
Explore all built-in profile references →

Content expanded · What’s new

Something missing or a source that needs attention?

Suggest a correction ↗