Start here
A few places to begin, from the aircraft’s story to the people who fly it.
Aircraft and simulator background
The Quickie Q200 uses two lifting wings arranged in tandem. Its elevators are on the forward wing and its ailerons on the rear wing. The reflexor changes the rear ailerons' neutral position, giving the pilot a control distinct from conventional wing flaps.
Quickie Q200
Developer · Read more ↗Two wings and independent trim
The manual places elevators on the forward wing and ailerons on the rear. Separate elevator and aileron trim controls accompany the reflexor, which raises the rear ailerons by shifting their neutral position. The control therefore differs from a conventional flap lever.
Quickie Q200
Developer · Read more ↗Fuel and cockpit equipment
Lionheart describes a 5 US gal header tank feeding the engine and a 15 US gal tank under the seats. An electric pump transfers fuel to the header tank. Its simulator cockpit includes GNS navigation equipment and a basic autopilot for flight assistance.
Quickie Q200
Developer · Read more ↗Meet Quickie Q200
The Quickie Q200 uses two lifting wings arranged in tandem. Its elevators are on the forward wing and its ailerons on the rear wing. The reflexor changes the rear ailerons' neutral position, giving the pilot a control distinct from conventional wing flaps.
Lionheart's rendition has independent elevator and aileron trims. The developer describes a two-seat fiberglass and Kevlar homebuilt with a 100 hp Continental O-200, alongside simulator navigation and autopilot equipment.
Quickie Q200
Quickie Aircraft → · Explore the family →
Quickie Q200
Developer · Quickie Q200 — developer reference ↗Aircraft type designators
No type designator selected for this reference.
History & design
A composite homebuilt translated to MSFS
The Q-200 is the Continental O-200-powered, two-seat member of the Quickie homebuilt world. Its glass-fibre and Kevlar airframe and unusual wing arrangement are part of an owner-built approach, so cockpit finishes and equipment vary. Lionheart describes rebuilding its earlier Flight Simulator artwork with MSFS materials and adding contemporary Asobo navigation equipment. The resulting panel and basic autopilot belong to this recreation, rather than defining every physical Q-200.
Developer · Quickie Q200 — developer reference ↗Lionheart developer introduction and conversion notes; aircraft and simulation equipment distinguished.
Systems & details
Two wings and independent trim
The manual places elevators on the forward wing and ailerons on the rear. Separate elevator and aileron trim controls accompany the reflexor, which raises the rear ailerons by shifting their neutral position. The control therefore differs from a conventional flap lever.
Fuel and cockpit equipment
Lionheart describes a 5 US gal header tank feeding the engine and a 15 US gal tank under the seats. An electric pump transfers fuel to the header tank. Its simulator cockpit includes GNS navigation equipment and a basic autopilot for flight assistance.
In your simulator
Systems, equipment and documentation for each developer’s aircraft.
MSFS 2020Lionheart Quickie Q200
Lionheart Creations · Released
Lionheart Quickie Q200
Lionheart Creations · Released
Manuals & resources
Find your next read
Choose a topic for a short introduction and a link to the original source. Simulator references identify the developer and edition they cover.
Developer documentation
Quickie Q200 — developer referenceQuickie Q200
Product description and feature list
Developer · Read the source ↗Quickie Q200 — developer referenceQuickie Q200
Original PDF pages 3-6,13,21,39
Developer · Read the source ↗Read the original documentation from the people who created it. Manuals open on their publisher’s website.
Developer documentation
Quickie Q200 — developer referenceDeveloper · Product description and feature list Quickie Q200 — developer referenceDeveloper · Original PDF pages 3-6,13,21,39Built-in force-feedback profiles
Read the documentary basis, editable starting settings and remaining questions for the aircraft you fly. Each explanation refers to the exact profile revision shown.
Catalogue programme-20261011-v3 · 2 profile choices
Lionheart Quickie Q200
Lionheart Creations · Free and Pro · Revision 3 · Inherited starting point
MSFS 2020
A two-seat tandem-wing homebuilt with elevators on the forward wing and ailerons on the rear wing.
Quickie Q200
Free and Pro · Revision 1 · Partial review
MSFS 2020 · MSFS 2024 · X-Plane 12
A two-seat tandem-wing homebuilt with elevators on the forward wing and ailerons on the rear wing.
Quickie Q200
A two-seat tandem-wing homebuilt with elevators on the forward wing and ailerons on the rear wing.
Aircraft and simulator scope
- Quickie Q200 · MSFS 2020 · Variant starting point
- Quickie Q200 · MSFS 2024 · Variant starting point
- Quickie Q200 · X-Plane 12 · Variant starting point
Universal named airframe/configuration; intended MSFS2020/MSFS2024/XP12 starting point, not add-on or edition acceptance. · Physical facts and prior documentary review are reused from their archived dated sources; new market availability is not inferred.
The simulator model and controls
A two-seat tandem-wing homebuilt with elevators on the forward wing and ailerons on the rear wing.
How this profile feels
Spring resistance builds with the selected airspeed response. A separate aerodynamic term adds speed-dependent control load.
Valid trim provides the configured pressure relief. Autopilot following is off.
Aircraft and configuration
Tandem-wing piston aircraft: elevators on front wing, ailerons on rear wing. Flexor/reflexor raises rear ailerons rather than conventional flaps.
Two wings and independent trim
The manual places elevators on the forward wing and ailerons on the rear. Separate elevator and aileron trim controls accompany the reflexor, which raises the rear ailerons by shifting their neutral position. The control therefore differs from a conventional flap lever.
Fuel and cockpit equipment
Lionheart describes a 5 US gal header tank feeding the engine and a 15 US gal tank under the seats. An electric pump transfers fuel to the header tank. Its simulator cockpit includes GNS navigation equipment and a basic autopilot for flight assistance.
About the values
Strengths are normalized hardware-feel settings. They set the effect balance; hand force depends on the device and its limits. The IAS reference is a tuning value.
What the documentation establishes
Quickie Q200: Tandem-wing piston aircraft: elevators on front wing, ailerons on rear wing. Flexor/reflexor raises rear ailerons rather than conventional flaps.
Documentary review and sources
These decisions describe the documentary basis and remaining gaps for this revision. Aircraft documentation and a starting setting describe different kinds of evidence.
Aircraft and variant
ReviewedA two-seat tandem-wing homebuilt with elevators on the forward wing and ailerons on the rear wing.
Flight controls
InheritedA two-seat tandem-wing homebuilt with elevators on the forward wing and ailerons on the rear wing.
Trim
InheritedThe manual places elevators on the forward wing and ailerons on the rear. Pitch authority 0.3 provides load relief and permitted centre movement; roll authority is 0.08.
Autopilot and stability
ReviewedAutopilot following is off; the configured spring and load retain the hardware feel.
Equipment
InheritedTandem-wing piston aircraft: elevators on front wing, ailerons on rear wing. Flexor/reflexor raises rear ailerons rather than conventional flaps.
Speeds and limits
InheritedThe indicated-speed references set the profile response scale; they are separate from aircraft operating limits.
Simulator integration
ReviewedThe profile targets msfs2020, msfs2024, xplane12. Add-on-specific controls use only the supported references configured by this profile.
Force-feedback settings
InheritedThe settings define the profile’s effect balance. Device output limits affect physical hand force.
Starting settings and their rationale
These configured values are starting estimates. The explanations describe what each setting controls; physical validation appears separately below.
| Setting | Starting value | What it controls and why |
|---|---|---|
| Spring strength | Starting value0.74 | What it controls and whyThe manual places elevators on the forward wing and ailerons on the rear. The baseline spring is 0.74. Its low-speed blend reaches baseline strength at 65 KIAS. |
| Master force gain | Starting value0.85 | What it controls and whyScales overall profile strength while preserving effect balance, subject to device and output limits. |
| Profile force gain | Starting value0.8 | What it controls and whyThe aerodynamic-load gain is 0.8 with an indicated-speed reference of 130 KIAS. This supplies speed-dependent loading alongside the spring. |
| Force tuning speed/reference | Starting value130.0 kt | What it controls and whySets the IAS reference for aerodynamic loading. It is an estimate, not published cruise TAS or a flight limit. |
| Spring response reference speed | Starting value65 kt | What it controls and whySets the IAS where the low-speed blend reaches baseline strength; high-speed stiffening also uses it. |
| Aileron force scale | Starting value0.72 | What it controls and whyRoll and pitch aerodynamic scales are 0.72 and 1, respectively. They set the aerodynamic axis balance. No custom spring-travel curve is enabled. |
| Elevator force scale | Starting value1 | What it controls and whyScales pitch aerodynamic loading; pitch spring travel and trim responses are separate settings. |
| Trim feel | Starting valueDisabled | What it controls and whyRetained for compatibility and group membership. Trim relief, rather than this flag, controls centre movement. |
| Trim relief | Starting valueEnabled | What it controls and whyAllows trim relief with supported control law and valid telemetry. Axis authorities set its amount. |
| Autopilot follow | Starting valueDisabled | What it controls and whyAutopilot following is off; the configured spring and load retain the hardware feel. |
| Autopilot neutral hold | Starting valueDisabled | What it controls and whyPermits centering hold during a supported AP state, separate from following a moving target. |
| Output force limit | Starting value0.55 | What it controls and whyCaps directed-force output. Native spring effects and device limits remain separate. |
All 44 starting settings and their rationale
The settings define the profile’s effect balance. Device output limits affect physical hand force.
| Setting | Starting value | What it controls and why |
|---|---|---|
| Spring strength | Starting value0.74 | What it controls and whyThe manual places elevators on the forward wing and ailerons on the rear. The baseline spring is 0.74. Its low-speed blend reaches baseline strength at 65 KIAS. |
| Profile force gain | Starting value0.8 | What it controls and whyThe aerodynamic-load gain is 0.8 with an indicated-speed reference of 130 KIAS. This supplies speed-dependent loading alongside the spring. |
| Elevator force scale | Starting value1 | What it controls and whyScales pitch aerodynamic loading; pitch spring travel and trim responses are separate settings. |
| Aileron force scale | Starting value0.72 | What it controls and whyRoll and pitch aerodynamic scales are 0.72 and 1, respectively. They set the aerodynamic axis balance. No custom spring-travel curve is enabled. |
| Output force limit | Starting value0.55 | What it controls and whyCaps directed-force output. Native spring effects and device limits remain separate. |
Quickie Q200: Separate pitch and roll relief approximate the documented trim axes; linkage geometry and add-on neutral scaling remain unmeasured. Estimated pitch/roll trim authorities 0.3/0.08; exact add-on sign, travel, units and build-specific neutral remain unqualified. Rudder trim never substitutes for roll trim.
| Setting | Starting value | What it controls and why |
|---|---|---|
| Elevator Authority | Starting value0.3 | What it controls and whyThe manual places elevators on the forward wing and ailerons on the rear. Pitch authority 0.3 provides load relief and permitted centre movement; roll authority is 0.08. |
| Aileron Authority | Starting value0.08 | What it controls and whyScales supported roll-trim relief and permitted centre movement. Zero removes roll response. |
Quickie Q200: 130.0 KIAS is the retained estimated tuning reference. It is not published cruise TAS, VNE, a new flight limit or a measured force threshold. Source-specific operating quantities remain attached to their original configuration and conditions.
| Setting | Starting value | What it controls and why |
|---|---|---|
| Force tuning speed/reference | Starting value130.0 kt | What it controls and whySets the IAS reference for aerodynamic loading. It is an estimate, not published cruise TAS or a flight limit. |
Exact configured values with software explanations. Force magnitudes remain editable estimates; disabled features retain inactive values.
| Setting | Starting value | What it controls and why |
|---|---|---|
| Spring deadband | Starting value0.04 | What it controls and whySets travel around the centre before the baseline spring resists. Smaller values engage it sooner. |
| Master force gain | Starting value0.85 | What it controls and whyScales overall profile strength while preserving effect balance, subject to device and output limits. |
| QBlend Enabled | Starting valueEnabled | What it controls and whyAllows baseline spring strength to rise with indicated airspeed where the control law permits it. |
| QSpring Minimum Factor | Starting value0.55 | What it controls and whySets low-speed spring strength as a fraction of baseline when blending is enabled. One keeps full strength. |
| QSpring Start Knots | Starting value8 kt | What it controls and whySets the IAS where the low-speed spring blend starts rising. This is a feel threshold, not a flight limit. |
| Spring response reference speed | Starting value65 kt | What it controls and whySets the IAS where the low-speed blend reaches baseline strength; high-speed stiffening also uses it. |
| Airspeed spring stiffening gain | Starting value0.15 | What it controls and whyThe high-speed spring-stiffening gain is 0.15. It strengthens the permitted spring response above 65 KIAS, with the squared-speed ratio capped at 5. |
| Airspeed spring stiffening limit | Starting value5 | What it controls and whyLimits the squared airspeed ratio used for high-speed spring stiffening; it is not a device-force cap. |
| Trim feel | Starting valueDisabled | What it controls and whyRetained for compatibility and group membership. Trim relief, rather than this flag, controls centre movement. |
| Trim relief | Starting valueEnabled | What it controls and whyAllows trim relief with supported control law and valid telemetry. Axis authorities set its amount. |
| Force Trim Enabled | Starting valueDisabled | What it controls and whyEnables local force trim, separate from aircraft-owned trim and add-on integration qualification. |
| GLoad Enabled | Starting valueEnabled | What it controls and whyAllows load-factor changes to modify permitted spring laws. Passive fly-by-wire feel can suppress it. |
| Rate Damping Enabled | Starting valueEnabled | What it controls and whyEnables rate damping with the configured coefficients and control law. |
| Autopilot follow | Starting valueDisabled | What it controls and whyAutopilot following is off; the configured spring and load retain the hardware feel. |
| Autopilot follow authority | Starting value0.1 | What it controls and whySets admitted AP-follow gain, not a percentage of travel. Runtime ownership and input limits still apply. |
| Autopilot neutral hold | Starting valueDisabled | What it controls and whyPermits centering hold during a supported AP state, separate from following a moving target. |
| Autopilot neutral hold strength | Starting value0.6 | What it controls and whySets admitted AP neutral-hold strength; inactive while neutral hold is disabled. |
| Enabled | Starting valueEnabled | What it controls and whyEnables aerodynamic cues; each still needs nonzero strength and its simulator conditions. |
| Gain | Starting value0.35 | What it controls and whySets stall-buffet strength. Zero removes the cue without changing simulator stalls or warnings. |
| Gain | Starting value0 | What it controls and whySets high-Mach buffet strength; onset and full-strength thresholds are separate. |
| Gain | Starting value0 | What it controls and whySets flap buffet at the configured position and speed gates. Flap movement texture is separate. |
| Maximum flap index | Starting value1 | What it controls and whySets the final flap index for detent normalization. UP plus three detents uses maximum index3. |
| Minimum flap index | Starting value1 | What it controls and whySets the first flap detent that admits buffet; this is a handle index, not degrees. |
| Gain | Starting value0 | What it controls and whySets gear aerodynamic buffet; movement and ground-contact cues are separate. |
| Shaker Enabled | Starting valueDisabled | What it controls and whyPermits shaker at supported warning conditions; the switch does not establish aircraft equipment. |
| Stick shaker amplitude | Starting value0.5 | What it controls and whySets triggered shaker strength; inactive while the shaker feature is disabled. |
| Enabled | Starting valueEnabled | What it controls and whyEnables ground effects; each still needs its own strength and contact or motion telemetry. |
| Gain | Starting value0.4 | What it controls and whySets rolling texture strength, modified by speed, surface and undercarriage configuration. |
| Gain | Starting value0.25 | What it controls and whySets gear-bump texture during ground motion, separate from touchdown impact. |
| Gain | Starting value0.65 | What it controls and whySets landing-impact strength; landing telemetry and response shape determine the pulse. |
| Gain | Starting value0 | What it controls and whySets reverse-thrust vibration with valid reverser and engine conditions. Zero removes the cue. |
| Enabled | Starting valueEnabled | What it controls and whyEnables engine cues with nonzero settings and valid running-engine telemetry. |
| Gain | Starting value0.12 | What it controls and whySets estimated engine vibration using configured telemetry and response, not measured cockpit vibration. |
| Enabled | Starting valueEnabled | What it controls and whyEnables accessory cues with configured strengths and observed accessory movement. |
| Gain | Starting value0 | What it controls and whySets texture from observed flap movement; a command without movement does not establish the cue. |
| Gain | Starting value0 | What it controls and whySets texture from observed gear movement, separate from aerodynamic and touchdown effects. |
Limits and open questions
- Quickie Q200 is a universal starting point; exact add-on matching, edition operation and physical hand-force calibration remain unqualified.
- Autopilot movement and unknown custom trim, failure or force-input signals are disabled. Confirm the selected equipment fit and trim direction for the implementation in use.
- Force magnitudes and speed tuning are editable inherited estimates. Owner physical and installed-aircraft acceptance remain pending.
Physical validation
No physical force validation is recorded in this public catalogue for this revision. Documentary review and software checks do not establish how a particular device feels.
Discuss this aircraft (0)
Questions, observations and useful sources from the community.
No published discussions yet. Bring a question or share a useful source.
Open aircraft discussions →Content expanded · What’s new
Something missing or a source that needs attention?
Suggest a correction ↗
