Start here
A few places to begin, from the aircraft’s story to the people who fly it.
Aircraft and configuration
Restauravia represents the P-36/H75 with retractable landing gear and flap settings of 15, 30 and 45 degrees. Its MSFS version 2 revises flight and engine parameters. The developer retains documented limitations for inactive or mispositioned cockpit controls.
Curtiss P-36/H75 Hawk
restauravia.fr · Read more ↗Meet Curtiss P-36/H75 Hawk
Restauravia represents the P-36/H75 with retractable landing gear and flap settings of 15, 30 and 45 degrees. Its MSFS version 2 revises flight and engine parameters. The developer retains documented limitations for inactive or mispositioned cockpit controls.
History & design
From Hawk 75 to P-36 service
The P-36 entered US Army Air Corps production in 1938. Hawk 75A aircraft served in European combat in 1939 and 1940. As newer fighters replaced it, the P-36 moved into training and courier duties in the United States.
National Museum of the United States Air Force · Curtiss P-36A Hawk ↗Museum history · P-36A and Hawk 75A family
The first delivered P-36A survives
The USAF Museum preserves the first P-36A delivered to the Army Air Corps, donated by Edward S. Perkins in 1959. Its markings represent the aircraft flown by Philip Rasmussen during the Pearl Harbor attack, rather than identifying the exhibit itself as that combat airframe. The museum records 243 P-36s acquired by the Air Corps, including 30 export P-36Gs taken over in 1942 after Norway’s occupation.
National Museum of the United States Air Force · Curtiss P-36A Hawk ↗USAF Museum P-36A; export Hawk 75 variants differ
Systems & details
Controls and equipment
Version 2 credits revised flight and engine parameters. Some controls remain inactive or incorrectly positioned.
X-Plane speed-table conflict
The X-Plane manual and model contain conflicting VNE and VNO values with unresolved units. Those values are not combined with the MSFS limits.
In your simulator
No released simulator product is listed for this aircraft in the developers reviewed. Announced products are excluded.
Manuals & resources
Find your next read
Choose a topic for a short introduction and a link to the original source. Simulator references identify the developer and edition they cover.
Simulator documentation
Controls and equipmentCurtiss P-36/H75 Hawk
Version 2 credits revised flight and engine parameters. Some controls remain inactive or incorrectly positioned.
H75 English manual · pages 2–7
restauravia.fr · Read the source ↗X-Plane speed-table conflictCurtiss P-36/H75 Hawk
The X-Plane manual and model contain conflicting VNE and VNO values with unresolved units. Those values are not combined with the MSFS limits.
X-Plane 12 original package and converted manual
restauravia.fr · Read the source ↗Read the original documentation from the people who created it. Manuals open on their publisher’s website.
Simulator documentation
Curtiss P-36/H75 Hawk — simulator documentationrestauravia.fr · H75 English manual · pages 2–7 Curtiss P-36/H75 Hawk — simulator documentationrestauravia.fr · X-Plane 12 original package and converted manualAircraft background
Curtiss P-36A HawkNational Museum of the United States Air Force · Museum history · P-36A and Hawk 75A familyBuilt-in force-feedback profiles
Read the documentary basis, editable starting settings and remaining questions for the aircraft you fly. Each explanation refers to the exact profile revision shown.
Catalogue programme-20261011-v3 · 2 profile choices
Restauravia Curtiss P-36/H75 Hawk
Restauravia · Free and Pro · Revision 2 · Inherited starting point
MSFS 2020 · MSFS 2024
The P-36/H75 Hawk family, with separate MSFS and X-Plane versions.
Restauravia Curtiss P-36 / H75 XP12
Restauravia · Free and Pro · Revision 2 · Inherited starting point
X-Plane 12
The P-36/H75 Hawk family, with separate MSFS and X-Plane versions.
Restauravia Curtiss P-36 / H75 XP12
The P-36/H75 Hawk family, with separate MSFS and X-Plane versions.
Aircraft and simulator scope
- Restauravia Curtiss P-36 / H75 XP12 · Restauravia · X-Plane 12 · Add-on starting point
The simulator model and controls
Restauravia Curtiss P-36 / H75 XP12 is the selected Restauravia configuration.
How this profile feels
Spring resistance builds with the selected airspeed response. A separate aerodynamic term adds speed-dependent control load.
Valid trim provides the configured pressure relief. Autopilot following is off.
Aircraft and configuration
Restauravia represents the P-36/H75 with retractable landing gear and flap settings of 15, 30 and 45 degrees. Its MSFS version 2 revises flight and engine parameters. The developer retains documented limitations for inactive or mispositioned cockpit controls.
Controls and equipment
Version 2 credits revised flight and engine parameters. Some controls remain inactive or incorrectly positioned.
About the values
Strengths are normalized hardware-feel settings. They set the effect balance; hand force depends on the device and its limits. The IAS reference is a tuning value.
Documentary review and sources
These decisions describe the documentary basis and remaining gaps for this revision. Aircraft documentation and a starting setting describe different kinds of evidence.
Aircraft and variant
InheritedRestauravia Curtiss P-36 / H75 XP12 is the selected Restauravia configuration.
Flight controls
InheritedThe P-36/H75 Hawk family, with separate MSFS and X-Plane versions.
Trim
InheritedThe profile uses the trim behaviour configured below. Pitch authority 0.3 provides load relief and permitted centre movement; roll authority is 0.
Autopilot and stability
InheritedAutopilot following is off; the configured spring and load retain the hardware feel.
Equipment
InheritedRestauravia represents the P-36/H75 with retractable landing gear and flap settings of 15, 30 and 45 degrees. Its MSFS version 2 revises flight and engine parameters. The developer retains documented limitations for inactive or mispositioned cockpit controls.
Speeds and limits
InheritedThe indicated-speed references set the profile response scale; they are separate from aircraft operating limits.
Simulator integration
InheritedThe profile targets xplane12. Add-on-specific controls use only the supported references configured by this profile.
Force-feedback settings
InheritedThe settings define the profile’s effect balance. Device output limits affect physical hand force.
Starting settings and their rationale
These configured values are starting estimates. The explanations describe what each setting controls; physical validation appears separately below.
| Setting | Starting value | What it controls and why |
|---|---|---|
| Spring strength | Starting value0.74 | What it controls and whyVersion 2 credits revised flight and engine parameters. The baseline spring is 0.74. Its low-speed blend reaches baseline strength at 65 KIAS. |
| Master force gain | Starting value0.85 | What it controls and whyScales overall profile strength while preserving effect balance, subject to device and output limits. |
| Profile force gain | Starting value0.8 | What it controls and whyThe aerodynamic-load gain is 0.8 with an indicated-speed reference of 180 KIAS. This supplies speed-dependent loading alongside the spring. |
| Force tuning speed/reference | Starting value180 kt | What it controls and whySets the IAS reference for aerodynamic loading. It is an estimate, not published cruise TAS or a flight limit. |
| Spring response reference speed | Starting value65 kt | What it controls and whySets the IAS where the low-speed blend reaches baseline strength; high-speed stiffening also uses it. |
| Aileron force scale | Starting value0.72 | What it controls and whyRoll and pitch aerodynamic scales are 0.72 and 1, respectively. They set the aerodynamic axis balance. No custom spring-travel curve is enabled. |
| Elevator force scale | Starting value1 | What it controls and whyScales pitch aerodynamic loading; pitch spring travel and trim responses are separate settings. |
| Trim feel | Starting valueDisabled | What it controls and whyRetained for compatibility and group membership. Trim relief, rather than this flag, controls centre movement. |
| Trim relief | Starting valueEnabled | What it controls and whyAllows trim relief with supported control law and valid telemetry. Axis authorities set its amount. |
| Autopilot follow | Starting valueDisabled | What it controls and whyAutopilot following is off; the configured spring and load retain the hardware feel. |
| Autopilot neutral hold | Starting valueDisabled | What it controls and whyPermits centering hold during a supported AP state, separate from following a moving target. |
| Output force limit | Starting value0.55 | What it controls and whyCaps directed-force output. Native spring effects and device limits remain separate. |
All 44 starting settings and their rationale
The settings define the profile’s effect balance. Device output limits affect physical hand force.
| Setting | Starting value | What it controls and why |
|---|---|---|
| Spring strength | Starting value0.74 | What it controls and whyVersion 2 credits revised flight and engine parameters. The baseline spring is 0.74. Its low-speed blend reaches baseline strength at 65 KIAS. |
| Spring deadband | Starting value0.04 | What it controls and whySets travel around the centre before the baseline spring resists. Smaller values engage it sooner. |
| Profile force gain | Starting value0.8 | What it controls and whyThe aerodynamic-load gain is 0.8 with an indicated-speed reference of 180 KIAS. This supplies speed-dependent loading alongside the spring. |
| Master force gain | Starting value0.85 | What it controls and whyScales overall profile strength while preserving effect balance, subject to device and output limits. |
| QBlend Enabled | Starting valueEnabled | What it controls and whyAllows baseline spring strength to rise with indicated airspeed where the control law permits it. |
| QSpring Minimum Factor | Starting value0.55 | What it controls and whySets low-speed spring strength as a fraction of baseline when blending is enabled. One keeps full strength. |
| QSpring Start Knots | Starting value8 kt | What it controls and whySets the IAS where the low-speed spring blend starts rising. This is a feel threshold, not a flight limit. |
| Spring response reference speed | Starting value65 kt | What it controls and whySets the IAS where the low-speed blend reaches baseline strength; high-speed stiffening also uses it. |
| Force tuning speed/reference | Starting value180 kt | What it controls and whySets the IAS reference for aerodynamic loading. It is an estimate, not published cruise TAS or a flight limit. |
| Airspeed spring stiffening gain | Starting value0.15 | What it controls and whyThe high-speed spring-stiffening gain is 0.15. It strengthens the permitted spring response above 65 KIAS, with the squared-speed ratio capped at 5. |
| Airspeed spring stiffening limit | Starting value5 | What it controls and whyLimits the squared airspeed ratio used for high-speed spring stiffening; it is not a device-force cap. |
| Aileron force scale | Starting value0.72 | What it controls and whyRoll and pitch aerodynamic scales are 0.72 and 1, respectively. They set the aerodynamic axis balance. No custom spring-travel curve is enabled. |
| Elevator force scale | Starting value1 | What it controls and whyScales pitch aerodynamic loading; pitch spring travel and trim responses are separate settings. |
| Output force limit | Starting value0.55 | What it controls and whyCaps directed-force output. Native spring effects and device limits remain separate. |
| Trim feel | Starting valueDisabled | What it controls and whyRetained for compatibility and group membership. Trim relief, rather than this flag, controls centre movement. |
| Trim relief | Starting valueEnabled | What it controls and whyAllows trim relief with supported control law and valid telemetry. Axis authorities set its amount. |
| Elevator Authority | Starting value0.3 | What it controls and whyThe profile uses the trim behaviour configured below. Pitch authority 0.3 provides load relief and permitted centre movement; roll authority is 0. |
| Aileron Authority | Starting value0 | What it controls and whyScales supported roll-trim relief and permitted centre movement. Zero removes roll response. |
| Force Trim Enabled | Starting valueDisabled | What it controls and whyEnables local force trim, separate from aircraft-owned trim and add-on integration qualification. |
| GLoad Enabled | Starting valueEnabled | What it controls and whyAllows load-factor changes to modify permitted spring laws. Passive fly-by-wire feel can suppress it. |
| Rate Damping Enabled | Starting valueEnabled | What it controls and whyEnables rate damping with the configured coefficients and control law. |
| Autopilot follow | Starting valueDisabled | What it controls and whyAutopilot following is off; the configured spring and load retain the hardware feel. |
| Autopilot follow authority | Starting value0.1 | What it controls and whySets admitted AP-follow gain, not a percentage of travel. Runtime ownership and input limits still apply. |
| Autopilot neutral hold | Starting valueDisabled | What it controls and whyPermits centering hold during a supported AP state, separate from following a moving target. |
| Autopilot neutral hold strength | Starting value0.6 | What it controls and whySets admitted AP neutral-hold strength; inactive while neutral hold is disabled. |
| Enabled | Starting valueEnabled | What it controls and whyEnables aerodynamic cues; each still needs nonzero strength and its simulator conditions. |
| Gain | Starting value0.35 | What it controls and whySets stall-buffet strength. Zero removes the cue without changing simulator stalls or warnings. |
| Gain | Starting value0 | What it controls and whySets high-Mach buffet strength; onset and full-strength thresholds are separate. |
| Gain | Starting value0 | What it controls and whySets flap buffet at the configured position and speed gates. Flap movement texture is separate. |
| Maximum flap index | Starting value3 | What it controls and whySets the final flap index for detent normalization. UP plus three detents uses maximum index3. |
| Minimum flap index | Starting value2 | What it controls and whySets the first flap detent that admits buffet; this is a handle index, not degrees. |
| Gain | Starting value0 | What it controls and whySets gear aerodynamic buffet; movement and ground-contact cues are separate. |
| Shaker Enabled | Starting valueDisabled | What it controls and whyPermits shaker at supported warning conditions; the switch does not establish aircraft equipment. |
| Stick shaker amplitude | Starting value0.5 | What it controls and whySets triggered shaker strength; inactive while the shaker feature is disabled. |
| Enabled | Starting valueEnabled | What it controls and whyEnables ground effects; each still needs its own strength and contact or motion telemetry. |
| Gain | Starting value0.4 | What it controls and whySets rolling texture strength, modified by speed, surface and undercarriage configuration. |
| Gain | Starting value0.25 | What it controls and whySets gear-bump texture during ground motion, separate from touchdown impact. |
| Gain | Starting value0.65 | What it controls and whySets landing-impact strength; landing telemetry and response shape determine the pulse. |
| Gain | Starting value0 | What it controls and whySets reverse-thrust vibration with valid reverser and engine conditions. Zero removes the cue. |
| Enabled | Starting valueEnabled | What it controls and whyEnables engine cues with nonzero settings and valid running-engine telemetry. |
| Gain | Starting value0.12 | What it controls and whySets estimated engine vibration using configured telemetry and response, not measured cockpit vibration. |
| Enabled | Starting valueEnabled | What it controls and whyEnables accessory cues with configured strengths and observed accessory movement. |
| Gain | Starting value0.12 | What it controls and whySets texture from observed flap movement; a command without movement does not establish the cue. |
| Gain | Starting value0.025 | What it controls and whySets texture from observed gear movement, separate from aerodynamic and touchdown effects. |
Limits and open questions
- Manual warbird stick with aerodynamic loading estimate; no hydraulic artificial feel or modern FBW.
- Conventional pitch relief estimate only; no unverified lateral gearing.
- No qualified AP output; follow/hold disabled.
- XP12 only. Overspeed texture disabled because manual280/220kt andACF460/350kt limits conflict; these values are not copied into the profile.
- 180 KIAS is an estimated control-feel reference, not cruise TAS, V-speeds or an operating limit.
- Spring 0.74, lateral scale 0.66, trim relief 0.18/0; editable estimates, not measured hand forces.
- Physical and installed-aircraft checks are deferred. Save this profile as the aircraft default if telemetry omits its developer or configuration.
- Only actual accessory-position changes drive movement textures. No pressure-dependent failures, guessed servo outputs or input compensation.
Physical validation
No physical force validation is recorded in this public catalogue for this revision. Documentary review and software checks do not establish how a particular device feels.
Discuss this aircraft (0)
Questions, observations and useful sources from the community.
No published discussions yet. Bring a question or share a useful source.
Open aircraft discussions →Content expanded · What’s new
Something missing or a source that needs attention?
Suggest a correction ↗